Thank you for choosing the Aube TH132, a programma- ble thermostat that provides both energy savings and total comfort.
below). TH132-A This model has been designed to control a room’s ambi- ent temperature. The TH132-A has one temperature sensor located in the control module. TH132-AF This model is designed to use a floor sensor to control the room temperature. The TH132-AF has two temperature sensors: • The first one, installed in the control module, controls the ambient temperature. • The second one, installed in the floor (and connected to the power base), limits the temperature of the floor (the default setting of this limit is 82°F). TH132-F This model is designed to control floor heating systems. The TH132-F has one temperature sensor installed in the floor (sensor is connected to the power base). The TH132 has two switches, located on the upper-left part on the rear of the control module, which are used to set the following options:
When the Early Start function is enabled (disabled by default), the TH132 calculat es the optimum system start time to obtain the desired temperature by the set time. To enable this function: Position switch #1 down. Note: When this function is enabled, the system can be activated before the pro- gram’s start time.
By default, the TH132 displays the temperature in °C. If you wish to change to °F: Position switch #2 up. Note: When you switch from °C to °F or vice versa, the , and setpoints must be redefined.
Align the bracket tabs on the control module with the holes located on top of the power base. This control module must be installed on a PB130 series power base. Note: Keep the thermostat's air vents clean and free from obstructions. Note: The screw cannot be removed completely. On the first installati on, the screen displays: 0:00, MO, and temperature (room/floor).
One of the two following messages may be dis- played when a problem occurs: LO : The floor temperature is below 32°F (0°C), or the temperature sensor is defective, or not connected. The heating indicator is displayed and the relay is closed (energized). HI : The floor temperature is above 140°F (60°C), or the temperature sensor is defective.
If you remove the module from its base for more than 2 hours, the time and day will have to be reprogrammed.
Comfort and Economy Setpoint sThese setpoints are associat ed with the schedule’s pro- grams (prog. 1 & 3 = Comfor t, prog. 2 & 4 = Economy) and are preprogrammed as follows: A & AF models— 68°F, 64°F F model— 82°F, 68°F To modify a setpoint:
n Set the temperature using and press and hold the or button until it is displayed on the screen.The vacation setpoint is associated to the Vacation oper- ating mode and is preprogrammed to 50°F. To modify this setpoint, repeat above steps.
The floor temperature limit is preprogrammed to 82°F to avoid damage to your floor. To modify, press the adjustment button (below ) using a pointed object, set the desi red temperature using and press MODE/RETURN to exit. The TH132 offers three operating modes:
Automatic — Exe cutes the schedule.program number is displayed. You can temporarily bypass the current program by setting a spec ific temperature setpoint or by selecting one of the pre-defined setpoint buttons ( ). The new setpoint will be maintained until the beginning of the next program.
View the manual for the Aube TH132 F here, for free. This manual comes under the category thermostat and has been rated by 1 people with an average of a 9. This manual is available in the following languages: English. Do you have a question about the Aube TH132 F or do you need help? Ask your question here
Do you have a question about the Aube and is the answer not in the manual?
Termostatul nu tine cont de temperatura setată , temperatura se ridica la 50 de grade. Ce trebuie facut in situatia aceasta? Va mulțumesc!
Same question Type your response here Add my commentIn the event that the thermostat does not consider the set temperature and the temperature increases to 50 degrees, you can attempt the following steps: 1. Check the programming: Make sure that the thermostat is programmed correctly with the desired set temperature. Use the "PGM" button to access the programming mode and verify the setpoints for Comfort, Economy, and Vacation modes. 2. Verify the operating mode: Ensure that the thermostat is in the correct operating mode. Press the "MODE" button to cycle through the available modes (Automatic, Manual, Vacation). Select the "Automatic" mode to execute the programmed schedule. 3. Check for sensor issues: Make sure that the temperature sensors are functioning properly. If the thermostat has a floor sensor (AF or F models), ensure that it is connected and not defective. If the floor temperature limit is set too high, it may cause the temperature to rise excessively. 4. Reset the thermostat: If the above steps do not resolve the issue, try resetting the thermostat. Please note that these steps are general guidelines and may vary depending on the specific model of the Aube TH132 thermostat.
This answer is automatically generated
Post reaction Gary Derrick January 22, 2023The Aube TH132 F thermostat screen keeps going blank, then it comes on for about 1 minute, and then goes blank again. Any ideas why? Thanks.
View photoThis message has been automatically translated Same question Type your response here Add my comment DimitraJanuary 31, 2024I keep setting the thermostat Aube TH132 F at 5 degrees and it keeps turning back to 19. I do not want any heating at all in my room as I keep the windows open 24/7. The electricity bill this month was insanely high and it is making me want to move out of the apartment. Any help?
View photoThis message has been automatically translated Same question Type your response here Add my comment Hilary IsherwoodApril 4, 2021My display screen has faded and is almost completely illegible. Does it need a new battery, and can I replace it myself?
Same question Type your response here Add my comment Vanessa McDonnell February 10, 2022The temperature is going up without being programmed. It is now 27 though was set at 19. How do I stop this? model TH132F
Same question Type your response here Add my commentHi Vanessa I have the same problem did you find a solution?
Post reaction Thomas FoxFebruary 5, 2023My controller screen has gone blank. I have checked and there is power getting to the controller. Even if the underfloor heating had failed in some way surely the screen should still light up in some way?
Same question Type your response here Add my comment Myles KELLEHER February 29, 2024Meaning of F in a circle, opposite the heating indicator?
Same question Type your response here Add my comment Malcolm CanningJanuary 25, 2021Control module TH 132 A/F/AF. Underfloor heating. Module windows all blank. Heating on permanently. Fuse OK. Help please !
Same question Type your response here Add my commentI've a TH132-F - display has gone blank - underfloor heating very hot. It's about 6 years old. Is it fixable or should I get a new one if so where do I get a replacement - located near Glasgow/Stirling UK
Post reaction MichelineDecember 11, 2022How can I override the system and just press on and off
Same question Type your response here Add my comment LukeFebruary 18, 2021Code 124 keeps coming up what does it mean
Same question Type your response here Add my comment Ask a questionBelow you will find the product specifications and the manual specifications of the Aube TH132 F.
The Aube TH132 F is a thermostat that is designed for efficient temperature control in residential settings. It is specifically developed to offer users reliable and accurate temperature regulation, promoting comfort and energy savings. This thermostat features a user-friendly interface, allowing for easy and intuitive operation. The clear display makes it convenient for users to monitor and adjust the temperature settings as desired. With its sleek and modern design, the Aube TH132 F can seamlessly blend with various home decors. The Aube TH132 F is equipped with advanced programming capabilities, enabling effective temperature management throughout the day. Users can create tailored schedules to suit their lifestyle, ensuring optimal heating or cooling at specific times. This feature allows for energy efficiency, reducing overall energy consumption and costs. Additionally, the Aube TH132 F incorporates energy-saving features such as adaptive intelligent recovery, which ensures that the desired temperature is reached at the scheduled time without unnecessary energy waste. This thermostat also offers precise temperature control, maintaining set temperatures within a narrow range for increased comfort. Installation of the Aube TH132 F is straightforward, and it is compatible with most heating and cooling systems. It is designed to be durable and reliable, providing long-lasting performance. With its high-quality construction, this thermostat can withstand the demands of daily use. Overall, the Aube TH132 F is a reliable and efficient thermostat that offers precise temperature control and energy-saving capabilities for greater comfort and reduced energy consumption in residential environments.
| Brand | Aube |
| Model | TH132 F |
| Product | thermostats |
| Language | English |
| Filetype | User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Aube TH132 F below.
The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.
If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.